Skip to main content

🔥 Dostawa: Zamów dziś do 12:00, dostawa jutro

English / €
Open search engine
Search
Close search engine Clear Search
Products in the cart: 0. See details
Your cart is empty

3powers by Otomatic

Three Cleaning Steps. Less Operator Involvement.

3Powers combines pneumatic, hydrodynamic and thermal cleaning in one automatic DPF | FAP cleaning cycle. It automates all three steps, including preparation and final treatment normally performed manually with traditional hydrodynamic cleaning machines. You save time, reduce manual work and free your team to focus on other workshop tasks.

SEE THE DIFFERENCE

Process 3Powers Conventional
hydrodynamic cleaning
(1/3) Filter preparation before wet cleaning AUTOMATIC MANUAL
(2/3) Wet cleaning and Hot-air drying AUTOMATIC AUTOMATIC
(3/3) Final air blow-through after drying AUTOMATIC MANUAL

(1/3) AIR IMPACT PULSE

Automatic preparation for easier wet cleaning

Inside a DPF is a ceramic core with many narrow channels separated by porous walls. Soot and ash can accumulate both in the channels and within the microscopic pores of these walls, restricting flow and making it harder for the cleaning solution to pass through.

Water is roughly 800 times denser than air at atmospheric pressure and is almost incompressible. When flow through a heavily blocked filter is restricted, excessive pressure can push against the ceramic core, potentially shifting it inside the housing or damaging it.

Even a gentle water-only flow does not provide the same mechanical action as dry pneumatic preparation. It can wet the deposits without sufficiently loosening them. Soot and ash may then form a thick, muddy mixture that can further restrict flow if it is not flushed out.

AIR IMPACT PULSE loosens deposits while they are still dry. Powerful impact pulses from a dedicated inflator detach deposits from the channel walls, making them easier to wash away during ACTIVE WATER FLUSH.

Without automatic pneumatic preparation, the operator carries out this step manually. 3Powers does it automatically, saving operator time and reducing manual work.

During manual blow-through, the operator comes into contact with soot and ash expelled from the filter, usually with the machine cabinet open. AIR IMPACT PULSE performs this step automatically inside the fully closed machine cabinet, helping reduce the operator’s contact with airborne dust and making the work cleaner and more comfortable.

2/3) ACTIVE WATER FLUSH

Better contact with deposits. More effective washing.

This stage is commonly known as hydrodynamic cleaning. After AIR IMPACT PULSE has loosened soot and ash, the deposits need to be washed out of the filter.

Plain water can struggle to wet soot and oily residues. OTOMATIC detergents lower the water’s surface tension and improve wetting, helping the cleaning solution spread over deposits and reach fine pores and difficult-to-access areas.

The flowing solution helps lift deposits from the channel walls and carries the released particles out of the filter. Compressed air pulses support this washing action.

Better wetting and effective flushing make soot and ash easier to remove. The filter then moves to THERMO AIR PULSE for drying and final removal of fine residues.

(3/3) THERMO AIR PULSE

Drying and final cleaning in one automatic stage

This is the thermal cleaning stage of 3Powers, combining hot-air drying with final impact-pulse cleaning.

After wet cleaning, some cleaning liquid can remain inside the filter channels and pores. In machines without a separate clean-water rinse before drying, this liquid still contains detergent and may carry fine soot and ash particles.

As the filter dries, the water evaporates, but ash and non-volatile detergent residues can remain. It is similar to a drop of dirty water drying on a surface: the water disappears, but a mark is left behind. A dry filter can therefore still contain cleaning residues.

A drying blower provides airflow to carry moisture away. This airflow alone may not be enough to dislodge the remaining particles.

THERMO AIR PULSE combines hot-air drying with powerful impact pulses from a dedicated inflator. Hot air dries the filter and the remaining deposits. The impact pulses then help dislodge and blow the dry particles out of the channels.

This completes the process beyond wet washing and drying alone. Where the final blow-through would otherwise require manual work, 3Powers performs it automatically, saving operator time and reducing involvement.